Anti-Static Conductive Primer

Mixing and Application Instructions (1444C)

Product Storage
THIS PRODUCT IS NOT FOR A CONDUCTIVE COATING SYSTEM. THIS SYSTEM IS NOT INTENDED FOR AREAS EXPOSED TO EXPLOSIVE MEDIA SUCH AS AMMUNITION PLANTS. THIS MATERIAL IS PROVIDED AS A STATIC DISSIPATIVE COATING. REVIEW THE DATA ON THE FRONT SIDE OF THIS TECHNICAL DATA UNDER ELECTRICAL RESISTANCE FOR TESTING RESULTS. REVIEW YOUR ELECTRICAL RESISTANTCE REQUIREMENTS BEFORE INSTALLING THIS PRODUCT. DO NOT USE WAXES UNLESS THEY ARE SPECIFICALLY FORMULATED AND RECOMMENDED FOR ANTI STATIC APPLICATIONS. ALWAYS APPLY TEST PATCHES OF YOUR SELECTION TO CHECK CONDUCTIVITY PRIOR TO APPLICATION AND TO BECOME FAMILIAR WITH THE PRODUCTS APPLICATION PROCEDURE. <br> Store product in an area so as to bring the material to normal room temperature before using.
Surface Preparation
Surface preparation will vary according to the type of system to be applied. For a one or two coat thin build system (3-10 mils dry) we recommend either mechanical scarification or acid etching until a suitable profile is achieved. For a complete system build higher than 10 mils dry, we recommend a fine brush blast (shot blast). All dirt, oil, dust, foreign contaminants and laitance must be removed to assure a trouble free bond to the substrate. A test should be made to determine that the concrete is dry; this can be done by placing a 4'x4' plastic sheet on the substrate and taping down the edges. If after 24 hours, the substrate is still dry below the plastic sheet, then the substrate is dry enough to start coating.
Product Mixings
(1444C) Mix one part A to one part B by volume. After the two parts are combined, mix well with slow speed mixing equipment such as a jiffy mixer until the material is thoroughly mixed and streak free. Improper mixing may result in product failure. Suitable mixing equipment may be necessary to remix in settled metallic pigment.
Product Priming
Product Application
This product is intended for the professional applicator with knowledge of this type of product. The mixed material can be applied by brush or roller. Maintain temperatures within the recommended ranges during the application and curing process. The 1444C conductive primer is best earthed with strips of copper about 20 centimeters long, which are anchored in the subfloor and connected to a water pipe or neutral conductor in the electric wiring system. Two earthing points normally suffice for a single room. One earth per 200 square meters of floor space is the general rule for large areas. After the substrate is earthed, Apply the 1444C by roller or brush at the recommended (5-7 Mil) thickness. Too thick of an application may result in insufficient conductivity or solvent entrapment and subsequent product failure. Allow sufficient time for the 1444C to cure. SEE FRONT SIDE UNDER LIMITATIONS FOR TESTING PROCEDURES.
Recoating or Topcoating
This product is intended for the professional applicator with knowledge of this type of product. The mixed material can be applied by brush or roller. Maintain temperatures within the recommended ranges during the application and curing process. The 1444C conductive primer is best earthed with strips of copper about 20 centimeters long, which are anchored in the subfloor and connected to a water pipe or neutral conductor in the electric wiring system. Two earthing points normally suffice for a single room. One earth per 200 square meters of floor space is the general rule for large areas. After the substrate is earthed, Apply the 1444C by roller or brush at the recommended (5-7 Mil) thickness. Too thick of an application may result in insufficient conductivity or solvent entrapment and subsequent product failure. Allow sufficient time for the 1444C to cure. SEE FRONT SIDE UNDER LIMITATIONS FOR TESTING PROCEDURES.
Cleanup
This product is intended for the professional applicator with knowledge of this type of product. The mixed material can be applied by brush or roller. Maintain temperatures within the recommended ranges during the application and curing process. The 1444C conductive primer is best earthed with strips of copper about 20 centimeters long, which are anchored in the subfloor and connected to a water pipe or neutral conductor in the electric wiring system. Two earthing points normally suffice for a single room. One earth per 200 square meters of floor space is the general rule for large areas. After the substrate is earthed, Apply the 1444C by roller or brush at the recommended (5-7 Mil) thickness. Too thick of an application may result in insufficient conductivity or solvent entrapment and subsequent product failure. Allow sufficient time for the 1444C to cure. SEE FRONT SIDE UNDER LIMITATIONS FOR TESTING PROCEDURES.
Floor Cleaning
This product is intended for the professional applicator with knowledge of this type of product. The mixed material can be applied by brush or roller. Maintain temperatures within the recommended ranges during the application and curing process. The 1444C conductive primer is best earthed with strips of copper about 20 centimeters long, which are anchored in the subfloor and connected to a water pipe or neutral conductor in the electric wiring system. Two earthing points normally suffice for a single room. One earth per 200 square meters of floor space is the general rule for large areas. After the substrate is earthed, Apply the 1444C by roller or brush at the recommended (5-7 Mil) thickness. Too thick of an application may result in insufficient conductivity or solvent entrapment and subsequent product failure. Allow sufficient time for the 1444C to cure. SEE FRONT SIDE UNDER LIMITATIONS FOR TESTING PROCEDURES.
DISCLAIMER OF WARRANTIES AND LIMITATIONS ON OUR LIABILITY

Epoxy Training

Concrete Patchwork 101Epoxy Preparation using our one-to-one mixing material that can be found on our epoxysolids.com website.Posted 7 months ago

Tooling 101Epoxy Flooring "Tooling" is important. Our Contractors Kit is available for our professional epoxy installations.Posted 7 months ago

Epoxy Mix areaPreparationPosted 7 months ago

Mixing 101Clear EpoxyPosted 7 months ago

Squeegee 101Epoxy FlooringPosted 7 months ago

Rolling Red EpoxyFirst CoatPosted 6 months ago

Scrapping ChipsPolymer Flake SystemPosted 6 months ago